SAE-J1516布置工具参考点中文版

SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely

voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.”

SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.

QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243

TO PLACE A DOCUMENT ORDER; (724) 776-4970 FAX: (724) 776-0790

SAE WEB ADDRESS http://www.wendangwang.com

Copyright 1998 Society of Automotive Engineers, Inc.

All rights reserved.

SAE-J1516布置工具参考点中文版

SAE-J1516布置工具参考点中文版

Printed in U.S.A.SURFACE VEHICLE 400 Commonwealth Drive, Warrendale, PA 15096-0001RECOMMENDED PRACTICE Submitted for recognition as an American National Standard J1516REAF.DEC1998Issued 1985-10

Reaffirmed

1998-12Superseding J1516 MAR90

Accommodation Tool Reference Point Foreword—This Reaffirmed Document has not changed other than to put it into the new SAE Technical Board

format. Definitions have been changed to Section 3. All other section numbers have changed accordingly.

1.Scope—Reference lines have been developed to which driver workspace accomodation tools can be located

in vehicle space. The lines describe horizontal reference point locations as a function of vehicle H-point height

(H30). One reference line has been established for use in vehicles with H-point heights (H30) and steering

wheel diameters (W9) less than 405 and 450 mm, respectively. (Class A Vehicles) This point can be used to

reference appropriate workspace tools to accommodate a driver population with a male-to-female ratio of one-

to-one. Separate reference lines have been established for use in vehicles with H-point heights (H30) between

405 and 530 mm and steering wheel diameters (W9) between 450 and 560 mm with treadle type pedals.

(Class B Vehicles) See Figure 1. Three lines are available for use in Class B vehicles depending on the

percentages of males and females in the population the designer wishes to accommodate. Separate points

can be used to reference appropriate workspace tools to accommodate driver populations with male-to-female

ratios of 50:50, 75:25, and 90:10 to 95:5. Different procedures for locating Class A and Class B

accommodation tool reference lines in vehicle space have been established based on unique packaging

considerations of the two categories of vehicles.2.References 2.1Applicable Publications—The following publications form a part of the specification to the extent specified

herein. Unless otherwise indicated, the latest revision of SAE publications shall apply.

2.1.1SAE P UBLICATIONS —Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.

SAE J941—Motor Vehicle Driver's Eye Range

SAE J1052—Motor Vehicle Driver and Passenger Head Position

SAE J1100—Motor Vehicle Dimensions

SAE J1517—Driver Selected Seat Position

SAE J1521—Truck Driver Shin-Knee Position for Clutch and Accelerator

SAE J1522—Truck Driver Stomach Position

N. L. Philippart, R. W. Roe, A. J. Arnold, T. J. Kuechenmeister (1984), "Driver Selected Seat Position

Model," SAE Paper No. 840508, Detroit, MI.

M. S. Sanders (1983), "U.S. Truck Driver Anthropometric and Truck Workspace Study," Final Report

Submitted to: Society of Automotive Engineers, Inc., Warrendale, PA.

B. E. Shaw and M. S. Sanders (1984), "Female U. S. Truck Driver Anthropometric and Truck Workspace

Study," Final Report Submitted to: Society of Automotive Engineers, Inc., Warrendale, PA.

容纳性工具参考点

前言--这个重新确认的文档没有改变除了把它放入SAE技术委员会格式。在第三部分有改变的确定内容。其他部分相应修改。范围-参考线被发展用来确定哪个驾驶工作舱容纳工具被定位在汽车中,这

些线描述了水平参考点根据H30。一条参考线被建立使用,H30和W9小于405和450.相对的,A级车这点能被用来参考大致的工作舱工具来容

纳驾驶人群男女1:1比例。单独的参考线被建立使用H30在405和530之间W9在450和560之间带落地踏板的B级车见图1.三条线使用在B级车上

根据设计者希望容纳的人群中男女比例。单独的点能被用来参考大致工作舱工具来容纳驾驶人群(男女50:50、75:25、90:10,95:5),确定AB级车容纳工具参考线的位置的不同方法被建立基于两种汽车的单独的布置考虑。定义

Word文档免费下载Word文档免费下载:SAE-J1516布置工具参考点中文版 (共11页,当前第1页)

SAE J1516布置工具参考点中文版相关文档

最新文档

返回顶部