CD4098BMS December 1992

CMOS Dual Monostable Multivibrator Description CD4098BMS dual monostable multivibrator provides stable retriggerable/resettable one shot operation for any xed voltage timing application. An external resistor (RX) and an external capacitor (CX) control the timing for the circuit. Adjustment of RX and CX provides a wide range of output pulse widths from the Q and Q terminals. The time delay from trigger input to output transition (trigger propagation delay) and the time delay from reset input to output transition (reset propagation delay) are independent of RX and CX. Leading edge triggering (+TR) and trailing edge triggering (-TR) inputs are provided for triggering from either edge of an input pulse. An unused+TR input should be tied to VSS. An unused -TR input should be tied to VDD. A RESET (on low level) is provided for immediate termination of the output pulse or to prevent output pulses when power is turned on. An unused RESET input should be tied to VDD. However, if an entire section of the CD4098BMS is not used, its RESET should be tied to VSS. See Table 9. In normal operation the circuit triggers (extends the output pulse one period) on the application of each new trigger pulse. For operation in the non-retriggerable mode, Q is connected to -TR when leading edge triggering (+TR) is used or Q is connected to+TR when trailing edge triggering (-TR) is used. The time period (T) for this multivibrator can be approximated by: TX= 1/2RXCX for CX 3 0.01µF. Time periods as a function of RX for values of CX and VDD are given in Figure 8. Values of T vary from unit to unit and as a function of voltage, temperature, and RXCX. The minimum value of external resistance, RX, is 5k . The maximum value of external capacitance, CX, is 100µF. Figure 9 shows time periods as a function of CX for values of RX and VDD. CD4098BMS TOP VIEW CX1 1 2 3 4 5 6 7 8 16 VDD 15 CX2 14 RXCX (2) 13 RESET (2) 12+TR (2) 11 -TR (2) 10 Q2 9 Q2

Features High Voltage Type (20V Rating) Retriggerable/Resettable Capability Trigger and Reset Propagation Delays Independent of RX, CX Triggering from Leading or Trailing Edge Q and Q Buffered Outputs Available Separate Resets Wide Range of Output Pulse Widths 100% Tested for Quiescent Current at 20V 5V, 10V and 15V Parametric Ratings Standardized Symmetrical Output Characteristics Maximum Input Current of 1µA at 18V Over Full Package Temperature Range; 100nA at 18V and+25oC Noise Margin (Over Full Package/Temperature Range) - 1V at VDD= 5V - 2V at VDD= 10V - 2.5V at VDD= 15V Meets All Requirements of JEDEC Tentative Standard No. 13B,“Standard Speci cations for Description of‘B’ Series CMOS Devices”

Applications Pulse Delay and Timing Pulse Shaping Astable Multivibrator

Pinout

The output pulse width has variations of±2.5% typically, over the temperature range of -55oC to+125oC for CX= 1000pF and RX= 100k . For power sup

ply variations of±5%, the output pulse width has variations of±0.5% typically, for VDD= 10V and 15V and±1% typically, for VDD= 5V at CX= 1000pF and RX= 5k . The CD4098BMS is supplied in these 16-lead outline packages: Braze Seal DIP Frit Seal DIP Ceramic Flatpack H4T H1F H6W

RXCX (1) RESET (1)+TR (1) -TR (1) Q1 Q1 VSS

TERMINALS 1, 8, 15 ARE ELECTRICALLY CONNECTED INTERNALLY CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143| Copyright© Intersil Corporation 1999

File Number

3332

7-482